【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Moderators: FlyingAllen, Eva Liu

【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby FlyingAllen » 2013-12-04 5:34

Product Functions:
_DSC0342.jpg

1, Serial port Data-Transmission at S.Port BUS.
2, Analog Signal AD input via S.Port.

Specifications:
Mode: SP2UART
Operational Voltage: DC 4 -10 V
Weight: 3g
Size: 44mmX15mmX7mm
Current Draw: 20mA @5V
Operating Temperature Range: -40℃~85℃

Pins Definition:
1.jpg

2.jpg

3.jpg


Instruction manual download:
SP2UARTmanual.pdf
You do not have the required permissions to view the files attached to this post.
FlyingAllen
Zeble
Zeble
 
Posts: 173
Joined: 2013-08-05 7:18

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby FlyingAllen » 2013-12-04 5:36

UART Definition & Data-Transmission:

Baud Rate: 300 bps (default), 8N1, no parity.
The Baud Rate is possible to reconfiguration within 300bps, 600bps, 1200bps, 2400bps, 4800bps, 9600bps.
Capacity: Normal capacity (Mode 1) and High capacity (Mode 2)
4.jpg


To Enable Data-transmission at S.PORT BUS, the Host (Type A) and Remote (Type B) devices are requiring use as pair and set in same Capacity Mode.

Here we take the example by XJT module and X8R receiver to introduce how to Data-transmission at S.Port BUS:
- We definition the Host (Type A) is connect with XJT by S.Port, Remote (Type B) is connect with S.Port of X8R receiver.
(The Mode A and Mode B position is exchangeable)
_DSC0359.jpg
_DSC0358.jpg

- When input data from Type B UART port will output the same data at Type A UART port. Vice versa.
You do not have the required permissions to view the files attached to this post.
FlyingAllen
Zeble
Zeble
 
Posts: 173
Joined: 2013-08-05 7:18

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby FlyingAllen » 2013-12-04 5:38

Obtain AD analog input via X8R & SP2UART adapter:

Many customer contact us how to connect Frsky battery voltage sensor with X8R receiver, because the X8R receiver is not built-in the AD port, which is not support connection FBVS with X8R directly.

Now, you can, through this adapter:
5.jpg

The SP2UART have two ADC port, supporting link with external analog devices.

It is very simple, just need enable the ADC function by SHORT CIRCUIT S1/S2 & GND is ok, and now you can connect /solder the FBVS to SP2UART as connect with D8R-II plus rx.
You do not have the required permissions to view the files attached to this post.
FlyingAllen
Zeble
Zeble
 
Posts: 173
Joined: 2013-08-05 7:18

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby MikeBl » 2013-12-04 11:57

What are the Sport application IDs for the two analog ports by default?
If they are the same as those for A1 and A2 of a 'D' series receiver, then the existing code on the Taranis will have a problem with A1 as the X8R receiver voltage is mapped onto A1.

Mike.
MikeBl
Newbie
Newbie
 
Posts: 2
Joined: 2013-11-25 23:05

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby Adela » 2013-12-06 7:53

MikeBl wrote:What are the Sport application IDs for the two analog ports by default?
If they are the same as those for A1 and A2 of a 'D' series receiver, then the existing code on the Taranis will have a problem with A1 as the X8R receiver voltage is mapped onto A1.

Mike.

-Have sent the latest protocol by e-mail,pls check it!
Adela
Sagoon
Sagoon
 
Posts: 55
Joined: 2013-08-05 7:21
Location: Wuxi.JiangSu.China

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby bob195558 » 2014-01-07 0:44

Hi FlyingAllen,

When will it be (Smart Port to UART Converter, w/ 2 ADC ports: SP2UART) available in the US (Aloft Hobbies)?

Bob
bob195558
Newbie
Newbie
 
Posts: 7
Joined: 2014-01-02 15:15
Location: VT, USA

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby FlyingAllen » 2014-01-07 7:54

As i know Alofthobbies will upload this products on line very soon!
FlyingAllen
Zeble
Zeble
 
Posts: 173
Joined: 2013-08-05 7:18

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby beetnick » 2014-01-27 14:03

Hi
I tried to use FBVS with Smart Port to UART Converter and X8R....but without success.
I was asking in the German FPV Community Taranis Thread and someone told me .. same problem .. the solution doesn't work. The UART Converter just blinking (i think it's middel fast) but no values on taranis.

I had connect as show on linked picture below:
http://www.elektromodelle.ch/FBVS-X8R.jpg


Can you help?
beetnick
Newbie
Newbie
 
Posts: 1
Joined: 2014-01-25 0:10

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby Adela » 2014-01-28 1:02

beetnick wrote:Hi
I tried to use FBVS with Smart Port to UART Converter and X8R....but without success.
I was asking in the German FPV Community Taranis Thread and someone told me .. same problem .. the solution doesn't work. The UART Converter just blinking (i think it's middel fast) but no values on taranis.

I had connect as show on linked picture below:
http://www.elektromodelle.ch/FBVS-X8R.jpg


Can you help?

Yes,the ADC values of the sensor has not been added on Taranis,pls wait for next verion in a few days.
Adela
Sagoon
Sagoon
 
Posts: 55
Joined: 2013-08-05 7:21
Location: Wuxi.JiangSu.China

Re: 【New Product】S.PORT TO UART Converter, w/ two ADC Ports

Postby Tom B 1956 » 2014-02-15 17:09

HI

I was looking at this as way to start using a Castle serial link. I believe I could get the unit to take castles output and the converter would encapsulate to S.Port. but the format of the voltage and current values well thats the question. What info I have been looking for is the the packet information to see if I could build a kermit to accept inbound and out bound packets converting to the proper format. Castle provides the it's packaging protocols. I just need to find the FrSky side.

Tom B.
Tom B 1956
Newbie
Newbie
 
Posts: 1
Joined: 2014-02-15 16:55

Next

Return to Telemetry Sensors

Who is online

Users browsing this forum: No registered users and 1 guest

cron